Εισάγετε μια λέξη ή φράση σε οποιαδήποτε γλώσσα 👆
Γλώσσα:
Μετάφραση και ανάλυση λέξεων από την τεχνητή νοημοσύνη ChatGPT
Σε αυτήν τη σελίδα μπορείτε να λάβετε μια λεπτομερή ανάλυση μιας λέξης ή μιας φράσης, η οποία δημιουργήθηκε χρησιμοποιώντας το ChatGPT, την καλύτερη τεχνολογία τεχνητής νοημοσύνης μέχρι σήμερα:
- πώς χρησιμοποιείται η λέξη
- συχνότητα χρήσης
- χρησιμοποιείται πιο συχνά στον προφορικό ή γραπτό λόγο
- επιλογές μετάφρασης λέξεων
- παραδείγματα χρήσης (πολλές φράσεις με μετάφραση)
- ετυμολογία
Τι (ποιος) είναι UDP hole punching - ορισμός
UDP hole punching
NAT TECHNIQUE IN COMPUTER NETWORKING
UDP Hole Punching
UDP hole punching is a commonly used technique employed in network address translation (NAT) applications for maintaining User Datagram Protocol (UDP) packet streams that traverse the NAT. NAT traversal techniques are typically required for client-to-client networking applications on the Internet involving hosts connected in private networks, especially in peer-to-peer, Direct Client-to-Client (DCC) and Voice over Internet Protocol (VoIP) deployments.
Hole punching (networking)
COMPUTER NETWORKING TECHNIQUE
NAT Hole punching; NAT hole punching
Hole punching (or sometimes punch-through) is a technique in computer networking for establishing a direct connection between two parties in which one or both are behind firewalls or behind routers that use network address translation (NAT). To punch a hole, each client connects to an unrestricted third-party server that temporarily stores external and internal address and port information for each client.
Through-hole technology
.jpg?width=200)
![A box of [[drill bit]]s used for making holes in printed circuit boards. While tungsten-carbide bits are very hard, they eventually wear out or break. Making holes is a considerable part of the cost of a through-hole printed circuit board.](https://commons.wikimedia.org/wiki/Special:FilePath/Box of 02in pcb bits.jpg?width=200 "A box of [[drill bit]]s used for making holes in printed circuit boards. While tungsten-carbide bits are very hard, they eventually wear out or break. Making holes is a considerable part of the cost of a through-hole printed circuit board.")
![Axial- (top) and radial- (bottom) leaded [[electrolytic capacitor]]s](https://commons.wikimedia.org/wiki/Special:FilePath/Capacitors electrolytic.jpg?width=200 "Axial- (top) and radial- (bottom) leaded [[electrolytic capacitor]]s")
![Components like [[integrated circuit]]s can have upwards of dozens of leads, or ''pins''](https://commons.wikimedia.org/wiki/Special:FilePath/Integrated Circuit.jpg?width=200 "Components like [[integrated circuit]]s can have upwards of dozens of leads, or ''pins''")
![Through-hole devices mounted on the circuit board of a mid-1980s [[home computer]]. Axial-lead devices are at upper left, while blue radial-lead capacitors are at upper right](https://commons.wikimedia.org/wiki/Special:FilePath/MOS6581 chtaube061229.jpg?width=200 "Through-hole devices mounted on the circuit board of a mid-1980s [[home computer]]. Axial-lead devices are at upper left, while blue radial-lead capacitors are at upper right")
MOUNTING SCHEME USED FOR ELECTRONIC COMPONENTS THAT INVOLVES THE USE OF LEADS ON THE COMPONENTS THAT ARE INSERTED INTO HOLES DRILLED IN PRINTED CIRCUIT BOARDS AND SOLDERED TO PADS ON THE OPPOSITE SIDE MANUALLY OR BY AUTOMATED INSERTION MOUNT MACHINES
Through-hole; Thru-hole; Plated through hole; Plated-through hole; Plated through-hole; Axial-lead; Radial-lead; Non-plated through-hole; Non-plated through hole; NPTH; Non-Plated Through-Hole; Non Plated Through Hole; Plated Through-Hole; Plated Through Hole; Metallized through hole; Metallized through-hole; Metallized hole; Metallised through hole; Metallised through-hole; Metallised hole; Metalized through hole; Metalized through-hole; Metalized hole; Metalised through hole; Metalised through-hole; Metalised hole
Through-hole technology (also spelled "thru-hole"), refers to the mounting scheme used for electronic components that involves the use of leads on the components that are inserted into holes drilled in printed circuit boards (PCB) and soldered to pads on the opposite side either by manual assembly (hand placement) or by the use of automated insertion mount machines.
